JQC-3FF DATASHEET PDF

Buy Xiamen Hongfa Electroacoustic JQC-3FF/12VDC-1ZS() only $ at Pushbutton Switches & Relays|Relays datasheet, inventory and pricing. Buy Xiamen Hongfa Electroacoustic JQC-3FF/ZST() only $ at Pushbutton Switches & Relays|Relays datasheet, inventory and pricing. Buy Xiamen Hongfa Electroacoustic JQC-3FF/HS only $ at EasyEDA components online store LCSC. Pushbutton Switches & Relays|Relays .

Author: Vudorr Vot
Country: Malawi
Language: English (Spanish)
Genre: Technology
Published (Last): 25 July 2014
Pages: 500
PDF File Size: 6.91 Mb
ePub File Size: 4.6 Mb
ISBN: 407-6-80302-616-2
Downloads: 65602
Price: Free* [*Free Regsitration Required]
Uploader: Tojamuro

This page was last modified on 13 Juneat On the Arduino side there is: If it does – no need for any external components. Sign up using Email and Password.

Normally closed, which means that when the relay is off a digital low “0” is received from Arduino the device is ON Out1: Discussion View source History. We recommend using a swappable cable to do this with, as using a relay requires you to perform some minor surgery on the appliance’s cable.

By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. Sign up or log in Sign up using Google. Home Questions Tags Users Unanswered. The relay should have the positive wire of the device being used connected to “IN” and to “Out 1” as shown in figure 2, and any digital signal pin on the arduino end For example pin We will use “out1” for our example, using “out2” will simply reverse the logic, as explained above.

Tutorial: DFR0017 V2 Relay

Thank you for the answer. This voltage is consistent with the operating voltage on the relay”. So, using Out1 a “1” will turn on the device and a datsheet will turn off the device. Email Required, but never shown.

  BIOCAPITAL THE CONSTITUTION OF POSTGENOMIC LIFE PDF

Signal Vcc Ground On the appliance side there is: I am interpreting the picture of the printed circuit board of the relay module with accompanying darasheet as follows:. Make sure the appliance to be tinckered with is unplugged from mains. Sending a digital high or a “1” will trigger the relay.

From the trace on the board it would seem that the middle resistor 1 kOhm is attached to the “IN” pin serving exactly this purpose. Normally open, which means that when the relay is on a digital high “1” is received from Arduino the device is ON. Sign up using Facebook. Using single 5V jac-3ff jqc-3ff-s-z – safety advice required Ask Question.

I am jcq-3ff the picture of the printed circuit board of the relay module with accompanying notes as qjc-3ff By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of service datssheet, privacy policy and cookie policyand that your continued use of the website is subject to these policies. Cut and strip a portion of the positive wire so that you end up with two ends of the wire as shown in Figure 2.

The diagrams below should help you understand the layout of the relay board. Post as a guest Name. Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

  CD4009AE DATASHEET PDF

Xiamen Hongfa Electroacoustic JQC-3FF/12VDC-1ZS() – PDF Datasheet – Relays In Stock |

Retrieved from ” https: Do I need to add anything else for relay to work safely and dxtasheet The relay in use is: I’ll already tested wiring and relay using LED before posting.

As Ghanima was a bit more explicit I’ve marked his answer as accepted.

Moreover, it even looks vatasheet relay board has diode already above VCC terminalso I wouldn’t need extra diode on IN line? I’ve tested components on board and can confirm it has: Above is relay I’m using and everything works as expected using diagram below. Thank you very much for your answer, I hope this topic will be helpful for others too. No large currents here, nothing to worry. You could easily check this with an Ohmmeter or following the traces on the board.

I know people recommend having resistor and transistor on IN line too, but are these necessary in this particular type of relay? I understand such a question can sound silly for electrical engineer, but I’m software engineer venturing in electrical world and need some guidance.

Please be vary carful not to play with live circuits! Sending a digital low jqc-3rf “0” will disable the relay.