CISCO EIGRP COMMAND AND CONFIGURATION HANDBOOK PDF

INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE . interface configuration command to instruct EIGRP to use the received . Therefore, to connect disparate EIGRP sites, you must configure the neighbor command with LISP encapsulation on every CE in the network. Cisco Nexus Series NX-OS Unicast Routing Configuration Guide, .. The { ip | ipv6} passive-interface eigrp command suppresses neighbors from forming.

Author: Mijinn Mazugal
Country: Comoros
Language: English (Spanish)
Genre: Career
Published (Last): 8 December 2007
Pages: 63
PDF File Size: 19.46 Mb
ePub File Size: 2.42 Mb
ISBN: 998-6-88067-310-9
Downloads: 52455
Price: Free* [*Free Regsitration Required]
Uploader: Kagajinn

Austin config-keychain key 1 Identifies the key number. R1 configure terminal Enter configuration commands, one per line. Sample Chapter is provided courtesy of Cisco Press.

EIGRP configuration

An administrative distance of 75 is assigned to this summary route. You should carefully review the configuration for each router shown above.

Austin config-if no shutdown Enables the interface. The feasibility condition dictates that the reported distance the composite metric reported by a neighbor to reach a subnet is better lower than the currently best metric successor metric to reach the same subnet. Houston config-keychain-key key-string tower.

The subnet is reachable via next-hop link-local IPv6 address FE Austin config-router key configuratuon susannah. The topology consists of four routers and some of you configuratio have noticed that the topology is the same that we used for multi-area OSPFv3 configuration earlier in the chapter, and also uses identical Hanndbook addressing scheme. Houston config-if no shutdown Enables the interface. Home Guides About Blog Shop. Creates a standard ACL number 30 and explicitly permits the The remote subnet NOTE Setting the maximum-path to 1 disables load balancing.

  IMPERIO DE LIBERTAD LA HISTORIA DE AMWAY PDF

Austin config-keychain-key send-lifetime Inbound and Outbound Distribute List Route Filters Figure shows the network topology for the configuration that follows, which demonstrates how to configure inbound and outbound route filters to control routing updates using the commands covered in this chapter.

EIGRP Configuration| Step By Step Guide

The configuration settings are made with the maximum-paths and variance commands in EIGRPv6 router configuration mode, reached with the ipv6 router eigrp command. Houston config-router eigrp log-neighbor-changes Changes with neighbors will be displayed. As a result, networks The rest of the configuration simply enables EIGRPv6 on commandd interfaces using the ASN to associate with the interface, using the ipv6 eigrp asn command.

Adds a second line to ACL 30 that explicitly permits the Austin config-if ip authentication mode eigrp md5. Houston config-keychain-key accept-lifetime Austin config-keychain-key key-string tower.

Sample Chapter is provided configurationn of Cisco Press. Austin config-keychain-key accept-lifetime Identifies a key chain name, which must match the name configured configuratin interface configuration mode. Houston config-router no auto-summary Disables auto-summarization.

NOTE With the maximum-paths router configuration command, up to 32 equal-cost entries can be in the routing table for the same destination.

EIGRP Configuration With Packet Tracer

Router config-router passive-interface default Prevents the sending of hello packets out all interfaces. About Affiliates Cisco Systems, Inc.

Austin config-if ip authentication key-chain eigrp susannah. Houston config-keychain-key exit Returns to global configuration mode. Houston config-if clock rate Sets the clock rate. The default is four. Houston config-router no auto-summary.

Without it, an administrative distance of 5 is automatically applied to the summary route. EIGRPv6 then exchange messages allowing the routers to discover neighbors, form neighbor relationships, and finally advertise subnets along with the metric components for each route.

  JEDNOMINUTOWY MENEDER PDF

EIGRP configuration

Enables manual summarization for EIGRP autonomous system on this specific interface for the given address and mask. Austin config-router eigrp log-neighbor-changes Changes with neighbors will be displayed. Instructs the router to include routes with a metric less than or equal to n times the minimum metric route for that destination, where n is the number specified by the variance command. The verification and troubleshooting examples in this section will all use the topology shown earlier, composed of routers R1, R2, R3 and R4.

But we have included the explicit no shutdown command in router configuration mode to make sure EIGRPv6 works even if you happen to use an older IOS version to practice the example.

Figure shows the network topology for the configuration that follows, which demonstrates how to control redistribution with an outbound distribute list using the commands covered in this chapter.

About Affiliates Cisco Systems, Inc. The show ipv6 eigrp topology command provides more detailed topology information about the subnet, as shown below:. Both the routes have an AD 90 and metric and are listed on two separate lines.

See All Related Articles. As a result, the rest of the routers in the topology will not be aware of the subnet and will not be able to route packets to the subnet.