ASTM B367 PDF

Originally approved in Last previous edition approved in as B – 2 For referenced ASTM standards, visit the ASTM website. ASTM B(). Standard Specification for Titanium and Titanium Alloy Castings. standard by ASTM International, 11/01/ View all product details. ASTM B Standard Specification for Titanium and Titanium Alloy Castings.

Author: Sazilkree Kajizil
Country: Kazakhstan
Language: English (Spanish)
Genre: History
Published (Last): 18 July 2012
Pages: 217
PDF File Size: 16.79 Mb
ePub File Size: 13.27 Mb
ISBN: 687-3-11783-813-7
Downloads: 70947
Price: Free* [*Free Regsitration Required]
Uploader: Malaran

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Examination of Weld Preparation S3. Only original conforming test results or the conforming retest results shall be reported to the purchaser. Therefore product analysis for elements not listed in Table 1 shall not be required unless speci?

Historical Version s – view previous versions of standard. Unalloyed titanium plus 0. Small size castings may be such that marking must be limited consistent with the available area.

Xstm discontinuities exceed the acceptance limits, all castings in the lot shall be examined according to Category II. Product analysis limits shall be as speci? Tensile properties shall be determined using a strain rate of 0. Hardness shall be determined in the as-cast condition unless otherwise speci?

The producer shall not ship material which is outside the limits speci? The results shall conform to the requirements speci?

ASTM B – 13() Standard Specification for Titanium and Titanium Alloy Castings

Originally published as B — 61 T. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Last previous edition B — Areas to be inspected, methods and types of liquid penetrants to be used, developing procedure, and basis for acceptance shall be agreed upon between the producer and the purchaser. If the results of the retest conform to the speci? A superscript epsilon e indicates an editorial change since the last revision or reapproval.

  HANDBUCH DER SEXUALMAGIE PDF

All castings shall be supplied in the as-cast condition except when post-weld heat treatment is required wherein it shall consist of a stress relief performed at certain temperatures. The values given in parentheses are for information only. Link to Active This link will always route to the current Active version of the standard. Temperature, time at temperature, and atmosphere shall be as agreed upon between the producer and the purchaser.

If the pattern is supplied by the purchaser, the dimensions of the casting shall be as predicted by the pattern. Dimensional tolerances ashm be included on the casting drawing, 4.

Your comments are invited either for revision of this standard or for additional astmm and should be addressed to ASTM Headquarters. Astj frequency of the retest will double the initial number of tests.

ASTM B367 GB/T 15073 Industrial Titanium Pump Titanium Pump Casting

This is in accordance with the round-off method of Practice E Properties shall be determined in the as-cast condition unless otherwise speci? The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. This abstract is a brief summary of the referenced standard.

The stressrelief cycle shall be in accordance with 7. After heat treatment, the castings should be cooled in air or in the furnace to ambient temperature unless otherwise agreed upon between the purchaser and producer. Grade 18—Palladium added to titanium alloy 3AI The decision for stress relieving shall be made by the producer, unless otherwise agreed upon.

  EL NEKHELY ELECTRONICS PDF

Need not be reported. The chemical composition determined shall conform to the analysis in Table 1 within the check analysis variations shown in Table 2 or shall be subject to rejection by the purchaser.

ASTM B367 GB / T 15073 Titàn Graphite Ponp Distribisyon pou Vann

The producer shall maintain documentation on procedure and welder quali? The materials shall undergo chemical, pour, and product analysis to determine the chemical composition which shall conform to the requirements for nitrogen, carbon, hydrogen, iron, oxygen, aluminum, vanadium, tin, ruthenium, palladium, cobalt, molybdenum, chromium, nickel, niobium, zirconium, silicon, and titanium.

Liquid Penetrant Examination S2. The test report shall contain the results of the actual chemical analysis and other tests speci? If a casting is used for a hardness sample, indentations shall be made in a surface that will not be subsequently machined.

The stress-relief cycle shall be in accordance with 7. The surface of the castings shall be free of adhering mold material, scale, cracks, and hot tears as determined by visual inspection.

Time at temperature shall be a minimum of 1? Current edition approved Aug. Tensile Strength, min, 0. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but asym not provided as part of the standard. A number in parentheses indicates the year of last reapproval. Materials and Manufacture 5.